核电结构土-结相互作用分析分区混合计算方法

土-结构相互作用分析是核电结构进行抗震设计和安全评估的重要环节.在核电结构的土-结相互作用分析中,阻尼和非线性是影响结构反应的重要因素. 若采用频域分析,可以方便考虑阻尼,但需通过等效线性化来考虑非线性,不适合于强震作用下的土体非线性.若采用时域分析的逐步积分方法,适合于考虑非线性,但材料阻尼一般采用瑞利阻尼模型,除了紧靠指定阻尼比的少数几个振型外,其他振型的反应将受到瑞利阻尼模型所确定的大阻尼所抑制,造成地震反应与真实情形有较大差异.若采用时域分析的模态叠加法,可合理计入阻尼效应,但模态叠加法不能考虑非线性.因此,如何合理考虑阻尼和非线性是核电结构土-结相互作用分析需要关注的问题.基于此,本文提出一种模态叠加和时步积分结合的土-结相互作用分区算法.其中,出于安全性考虑,地震作用下核电主体结构一般不允许进入非线性,因此结构可采用模态叠加方法,以便合理考虑结构阻尼;土体和基础采用显式时步积分法,可考虑土体非线性;通过人工边界条件考虑无限域的影响 (辐射阻尼).通过简单算例对该方法进行了验证,并用于CAP1400核电结构的土-结相互作用分析中,对比分析了采用模态阻尼和瑞利阻尼时核电结构和场地反应的差异,结果表明结构阻尼模型对场地的反应影响不大,但对结构反应影响明显,在实际工程中应合理选取阻尼模型.      

Wave-based analysis of dual acoustic black holes for anechoic termination of shock testing devices

Shock testing is an important issue for the survivability of an equipment under shock environment in aerospace and military industries. One of the problems faced in conventional shock testing devices is the need for redesigning of the geometry whenever the responses to different shock environments are tested. To circumvent the redesigning processes, a structure with two ‘acoustic black holes (ABHs)’ on both ends, referred to as the beam with dual ABHs, is proposed as a shock testing device. The beam with dual ABHs is capable of simulating diverse shock environments by controlling the applied force because it can be regarded as an infinite beam at high frequency range with the aid of the anechoic terminations by the ABHs. To systematically investigate the beam with dual ABHs, we develop a wave-based method that uses the reflection matrix of an ABH to perform free and forced vibration analyses. From the analyses on frequency response function and shock response spectrum of the beam with dual ABH, it is suggested that the beam with dual ABHs is feasible as a semi-permanent shock testing device.     

Improved Reversible Zinc Storage Achieved in a Constitutionally Crystalline-Stable Mn(VO3)2 Nanobelts Cathode

Rechargeable zinc-ion batteries (ZIBs) are potential for grid-scale applications owing to their safety, low price, and available sources. The development of ZIBs cathode with high specific capacity, wide operating voltage window and stable cyclability is urgently needed in next-generation commercial batteries. Herein, we report a structurally crystalline-stable Mn(VO₃)₂ nanobelts cathode for ZIBs prepared via a facile hydrothermal method. The as-synthesized Mn(VO₃)₂ exhibited high specific capacity of 350 mAh g⁻¹ at 0.1 A g⁻¹, and maintained a capacity retention of 92 % after 10,000 cycles at 2 A g⁻¹. It also showed good rate performance and obtained a reversible capacity of up to 200 mAh g⁻¹ after 600 cycles at 0.2 A g⁻¹ under −20 °C. The electrochemical tests suggest that Mn(VO₃)₂ nanobelts impart fast Zn²⁺ ions migration, and the introduction of manganese atoms help make the structures more indestructible, leading to a good rate performance and prolonged cycle lifespan.     

2,3-Disubstituted Fluorene Scaffold for Efficient Green Phosphorescent Organic Light-Emitting Diodes

Fluorene is a classic three-membered polycyclic aromatic hydrocarbon, and it has been widely used in optoelectronic devices. Here we explore a simple and efficient strategy for the derivatization at the 2- and 3- positions in fluorene unit. By introducing different types of substituents, we design two pairs of 2,3-disubstituted fluorene isomers and use them as host materials for phosphorescent organic light-emitting diodes (PHOLEDs). The green PHOLEDs hosted by these fluorene derivatives realize high external quantum efficiencies (EQE) over 20 % with low efficiency roll-off. Particularly, the devices hosted by 2TRz3TPA and 2TPA3TRz achieve nearly 24 % EQE and 104 lm W⁻¹ power efficiency. These results clearly demonstrate that the 2,3-disubstituted fluorene platforms are potentially useful for constructing host materials.     

基于器件结构提高TADF-OLED器件的发光性能

为了提高以TADF材料作为主体、天蓝色荧光材料作为客体的混合薄膜的OLED器件光电性能,我们调整了器件结构,使主体材料发挥其优势。制备了基本结构为ITO/NPB(40 nm)/DMAC-DPS∶x%BUBD-1(40 nm)/Bphen(30 nm)/LiF(0.5 nm)/Al的OLED器件。研究了主-客体材料在不同掺杂浓度下的OLED器件的光电特性。为了提高主体材料的利用率,在空穴传输层和发光层之间加入10 nm的DMAC-DPS作为间隔层;然后,在阳极和空穴传输层之间加入HAT-CN作为空穴注入层,形成HAT-CN/NPB结构的PN结,有效降低了器件的启亮电压(2.7 V)。测量了有无HAT-CN的单空穴器件的阻抗谱。结果表明,在最佳掺杂比例(2%)下,器件的外量子效率(EQE)达到4.92%,接近荧光OLED的EQE理论极限值;加入10 nm的DMAC-DPS作为间隔层,使得器件的EQE达到5.37%;HAT-CN/NPB结构的PN结有效地降低了器件的启亮电压(2.7 V),将OLED器件的EQE提高到5.76%;HAT-CN的加入提高了器件的空穴迁移率,降低了单空穴器件的阻抗。TADF材料作为主体材料在提高OLED器件的光电性能方面具有很大的潜力。     

基于B3PyMPM∶Cs高效叠层OLED器件的制备

以B 3 PyMPM∶Cs/Al/HAT-CN作为电荷生成单元制备高效叠层绿色磷光有机电致发光器件,叠层器件的最大电流效率和最大流明效率分别为172.2 cd/A和111.0 lm/W,在5 mA/cm^2电流密度下,叠层器件的电压和亮度分别为传统器件的2.04倍和2.84倍.为了探究叠层器件性能优于传统器件的原因,研究了电荷生成单元内的电荷产生和注入过程,以及薄层铝对电子注入特性和电荷生成单元稳定性的影响.实验结果表明,电荷能够有效地在电荷生成单元内产生并顺利注入电子传输层中,B3PyMPM∶Cs和HAT-CN间Al薄层的插入能够进一步提高电子注入效率及器件结构的稳定性.     

氮低温制冷循环系统在大科学装置中的应用与发展

大科学装置中低温设备的氮低温冷量需要日益快速增长,为减少能耗和保障装置的长期稳定运行,基于大科学装置氮低温系统运行需求,介绍了氮低温制冷循环系统在国内外大科学装置中的应用情况,总结了目前大科学装置中应用氮低温制冷循环系统的研究现状,并探讨以氮制冷机为核心的氮低温制冷循环系统在未来大科学装置中发展方向。     

Design of a tuned vibration absorber for a slender hollow cylindrical structure

Abstract

In this paper, details of the design work for a tuned vibration absorber to be used on a hollow cylindrical structure is presented. The vibration problem is of resonant type and the tuned vibration absorber is designed to suppress the displacement vibration response of the free end of the slender hollow structure dominated by the contribution of its lowest transverse vibration modes. The structure is modeled using a commercial finite element software. Finite element model of the structure is verified using experimentally obtained frequency response functions and modal parameters. Effective parameters of the tuned vibration absorber design are then determined based on finite element analysis simulations of the vibration suppression performance of the tuned vibration absorber as it is used on the structure. Details of the tuned vibration absorber design are determined and a prototype is fabricated. Prototype tuned vibration absorber is then characterized experimentally both as a standalone system and also as it is used on the main structure. Vibration reduction performance of the physical prototype of the tuned vibration absorber is also compared with its vibration reduction performance estimated from finite element analysis simulations so that the analysis based design process can be validated.

Communicated by Dumitru Caruntu.